The M30 light kit includes everything you need to install a pair of lights to your choice of mounting location.
Two (2) Model 30 Off Road Led lights with standard bracket.
Plug n Play Wiring harness with waterproof switch.
Light controller / dimmer
Heavy duty light bracket
Xpel lens protection
About the Model 30
LED type: 3 Cree XP-G leds
Reflector: 3x shallow draw, AL deposition
Housing: Machined aluminum, black powder coat, openings sealed with orings to insure waterproofness.
Mount: Stainless steel with a wide range of vertical adjustment. The mount locks in place with stainless hardware including nyloc nut. 6mm bolt hole provides a secure mount to your choice of mounting locations. 25mm/1” square mount foot will mount to any flat location or stud. Includes stainless hardware to connect light to your mount.
Size: length 70mm , diameter 55mm. Same external size as the Model 60.
Weight:Approximately 8 oz. per light depending on options chosen.
Light Performance (single light)
Beam (degrees): 10 degree primary beam provides superior distance.
Light output (lumens): 1500
Color Temperature (kelvin): 5500
Usable Light (feet/meters): 500ft, Spot that deer, dog, animal/obstacle!
Power Usage: .9amps @12vdc or 10 watts, much reduced draw with a dimmer.
About the wiring harness
Plug n Play: No soldering, crimping or other wire prep required. When purchased with a dimmer, the dimmer will be integrated into the harness. Please leave a note during checkout where you prefer the dimmer be located.
Light Wiring: One meter wire lead with connector. Sheathed lead provides resistance to rubs, scraps and other potential damage while maintaining waterproofness. Adequate length for mounting on lower fork.
LED Control /Dimmer(optional): When purchased with a dimmer, the dimmer will be integrated into the harness. Please leave a note during checkout where you prefer the dimmer be located. The EZcan location is fixed (under seat) by the stock wiring, we extend the light leads and install amp connectors to plug into the EZcan. The rotary dimmer is typically installed towards the front of the bike on dash or handlebar. The wireless dimmer is typically installed under seat or in a fairing, very flexible installation due to the wireless nature. The bluetooth dimmer is typically installed under seat or in a fairing.
Custom: We can customize the wire lengths to meet your needs. Typically there will be adequate wire, with length to spare.
Switch: Your choice of 1)Waterproof push button on/off switch. Switch can be panel mounted (3/8" hole) or surface mounted with velcro or double sided tape. or 2) Handlebar mounted switch.
1 year from date of purchase to customer of record.
Check our store policies page for detailed information.
Posted by CRFer on 26th Nov 2019
My buddy has had these lights for several years and the are SUPER bright and well made. So, I had to get a set for my CR250L Rally. I bought the kit with the wiring harness, and the harness is a really nice piece as well. Comparable lights are three times the price.
Posted by Ethan on 2nd Sep 2019
Installed on the chin of my old rocket K1200RS. Combined these with a bluetooth dimmer set at 50% reduction on low beam, I think they make an excellent conspicuity light. On high beam / full power it reaches out very well. Nice focused beam with defined edge, then a soft spill to the side.
KRS has a momentary/flash to pass switch and I love having the bright spots to grab the attention of drivers who I think may pull out in front of me.
Seem to be very well made and sealed. Will see in the long term.
Dimmer is clever and easy to use, though i wish it was put in a smaller enclosure. I had space under my seat but on smaller sport bikes, or ADV bike I'll probably use the smaller dial type dimmer.
Over all these are a great set of lights. Far better quality and customer care than sketchy Amazon/Ebay vendors, and in my experience as good or better than the vastly overpriced / tragically underperforming lights I regret buying from Touratech & Twisted Throttle suppliers.